The Leading International Rubber Technology ExhibitionRead More
1. Product name, specification model and equipment weight size:
1.1 Product Name: Cold Feed Extruder
1.2 Specification model: XJWP-120X20D
1.3 Equipment weight: about 5 tons
1.4 Dimensions (length X width X height): about 4200X1200X1600mm
1.5 Equipment layout:
1. Special rubber head; 2. Fuselage; 3. Five-section automatic temperature control system; 4. Feed roller device; 5. Feed hopper; 6. AC motor; 9. AC speed control cabinet; 10. Screw cooling Device; 11. Base.
2. Main technical performance parameters:
2.1 Screw diameter: Ф120nn
2.2 Working length of screw: 1920mm
2.3 Screw length to diameter ratio: 20:1
2.4 Screw speed: 4.5-45r/min
2.5 Drive motor power: 110kw-1500r/min
2.6 Power conditions: 3-phase, 380V
2.7 Adapted Mooney viscosity: ML (1+4) 100℃ 50-90
2.8 Design output: 500-600KG per hour
3. Technical description
3.1.1 Screw: (customized outsourcing)
A. Material: 38CrMoALA;
B. The surface is nitrided;
C. Hardness ≥ HRC62
D. Nitrogen layer depth ≥0.55mm
E. Structure: Adopts German Telest structure, with good extrusion stability and large glue output.
a. It has a hollow structure over the entire length of the screw to facilitate temperature control.
b. The rotation direction of the thread of the rotary joint is opposite to that of the screw.
c. The screw head size is according to the enterprise standard.
d. Do 10kg/cm2 inside the screw for more than 1 hour water pressure test without leakage.
3.1.2 Barrel and bushing:
a. Welded structure, tempered after welding, do 10kg/cm2, hydraulic test for more than 1 hour, no leakage.
b. The fuselage flange connected to the machine head can be processed according to customer requirements.
B. Bush: with exhaust port, the exhaust port does not run rubber
a. Material: 38CrMoALA;
b. The surface is nitridized, and our factory heat treatment workshop has imported nitriding furnace;
c. Hardness ≥ HRC66;
d. Nitrogen layer depth ≥0.55mm;
3.1.3 Feeding roller: structure obtained national patent
A. Material: 38CrMoALA, roller surface nitriding treatment, hardness ≥HRC62, hard layer depth ≥0.55mm;
a. Internal circulation of water;
b. Can be connected to rotary joint;
c. The feed roller gear is made of 20CrMoTi, and the surface is carburized. The average depth of carburizing is 1.5mm;
d. The feed roller is driven by the gear reducer shaft through the gear, and the speed ratio gear has sufficient strength and wear resistance;
e. The speed ratio gear is lubricated with grease;
f. There is a rubber scraper to scrape off the rubber material on the surface of the roller. The scraper is fixed on the barrel and the gap between the roller and the roller can be adjusted. The feeding roller can be rotated and opened;
g. The feed roller bearing is lubricated with grease.
220.127.116.11 Design conditions
A. Working condition coefficient ≥ 1.75
18.104.22.168 Three-stage transmission, parallel shaft output, noise less than 85db(A);
22.214.171.124 The output shaft has a hollow structure, the screw is inserted into it and transmits torque;
126.96.36.199 with peep window;
188.8.131.52 has oil mark with scale and oil outlet with plug;
184.108.40.206 A lubrication system composed of independent lubricating oil pumps, etc., to facilitate forced lubrication of gears and bearings;
220.127.116.11 The top of the gearbox is equipped with an exhaust valve, and the oil outlet of the gearbox is located at the lowest part of the box;
3.1.5 Temperature control pipeline:
18.104.22.168 The pipeline is arranged on the operation side of the extruder row;
22.214.171.124 The soft connecting pipe should be resistant to temperatures above 120℃;
126.96.36.199 All valves have nameplates;
188.8.131.52 Hydrostatic test, under 10kg/cm2, under 1 hour of hydrostatic test, there is no leakage;
A. The extruder and the motor are installed on the same base;
B. Pins should be positioned between the upper and lower case of the gearbox;
C. The base has sufficient strength and rigidity to withstand the torque and vibration loads of the extruder;
D. Rough machining the surface of the base for installation and connection;
E. There are more than two planes on the base to facilitate installation and alignment;
F. After the standard is installed, the center mark will be printed on the extruder, gearbox and machine base;
G. There are lifting hooks or lifting holes for lifting;
H. The area of the base is as small as possible, but fully leave the motor installation position;
3.1.7 Temperature control device
184.108.40.206 Structure and working principle:
The system adopts forced circulation of media, and controls the temperature of each section independently in six units. Each unit is composed of a water pump, an electric heater, a temperature control instrument, a cooling water on-off solenoid valve, an automatic exhaust valve, a platinum thermal resistance, and an electrical contact pressure. Table (shockproof) and other components, the circulating water pump injects the medium (softened water) into the electric heater (the automatic exhaust valve discharges the gas in the system), flows through the barrel through the pipeline, the machine head, and the screw return to the suction port of the pump After the temperature of each section is set, the circulating water will heat the barrel, head, screw, etc. through the heater or heat the barrel, head, screw, etc. in the working state due to the heat generated during the rubber material processing, Heat is discharged through circulating water, heating power per unit: 6KW, control temperature range: room temperature-90℃; control temperature accuracy: ± 2℃; (using imported constant temperature machine)
220.127.116.11 Unit description
The first unit: control the screw temperature;
The second unit: control the temperature of the extrusion section of the barrel;
The third unit: controlling the temperature of barrel plasticizing section I;
Unit 4: Control the temperature of barrel plasticizing section II;
Unit 5: Control the temperature of barrel plasticizing section III;
Unit 6: Control the temperature of the feeding section of the barrel;
Unit 7: Control the head temperature.
18.104.22.168 Suppliers and models of main supporting parts
Circulating water pump: German Wilo Company
Temperature regulator: Omron
3.1.8 Electrical control system:
The extruder is controlled by a DC drive and has protection functions such as overcurrent, overload, phase loss, undervoltage, demagnetization, and zero speed start of the main motor;
4. Details of main supporting parts
Zhejiang Special Motor Manufacturing Co., Ltd.
solid state relay
Automatic disconnection, buttons, indicator lights, etc.
5. Power conditions
5.1 Main power supply: 3~~~380V/50Hz
5.2 Control power supply: 1~~~220V/50Hz
5.3 Water: 2kg/cm2
6. Coloring: Standard
A. Extruder, frame;
B. Temperature control;
C. Safety cover;
6.2 Paint method
A. Anti-rust primer: 2 layers
B. Toning topcoat: 2 layers
7. Noise and vibration:
7.1 Noise: 1 meter away from the equipment, noise ≤85dB(A)
7.2 The deviation of the center line between the motor and the reducer:
1) Angle deviation: 10/10mm
2) Center height difference: 5/100mm
8. Inspection and acceptance
8.1 Inspection before leaving the factory: In addition to the inspection according to the manufacturing process of the equipment itself, special inspections are also carried out on the following items;
a. Screw and barrel dimensions;
b. Hardness of screw and barrel material.
ZHEJIANG BAINA Rubber& Plastic Equipment Co,Ltd.,was founded in 1998 with a total investment of 20 million USD which,is a professional manufacturer of complete plants and products of rubber and plastic.it is a national high and new technology enterprise.medium and small-sized enterprise of Zhejiang province,and municipal innovation pilot enterprise.Located in modern Industrial Zone,Xianju County,it covers area of more than 53000 squar meters.
As a leader enterprise, Baina has focused on the development and production of rubber and plastic equipments and products for many years. In term of the equipments our main products includes rubber extruders, three (four) composite microwave vulcanization production line，salt bath vulcanization production line, NBR and PVC air conditional insulation hose vulcanization production line, steel edge rubber water proof vulcanization production line, silicone rubber vulcanization production line and such rubber and plastic equipments. In term of the products, we have automotive air conditioning hoses, bathroom tubes, braided tubes, rubber sealing strips and low density EPDM blowing articles. Our equipments are exported to America, Japan, Russian, Israel，South Korea, Turkey, Saudi Arabia and so on. Our annual output is more than 200 production lines. We offer equipments and technical support to more than 1000 famous rubber production enterprises in domestic and oversea market, and maintain long-term cooperation partners relationship.
Our company has a provincial research center with abundant R＆D strength, cooperates with many domestic higher institutions, and also has advanced international rubber COTS and laboratory equipments. Recently，we have 15 authorized patents(includes 5 invention patents), and 12 provincial level scientific research projects such as national torch plan, national key new product project in the nearly three years. Some fileds of our company have reached the international advanced level.
We sincerely invite customers from home and abroad to make a field inspection to our company. And we are looking for long-term relationship with you for our common promising future.
We always adhere to the enterprise tenet of “high standard, refined and zero defect”, regard quality as life, lead industry development, and create a foundry industry with core competitiveness and core value, in line with “sincere and pragmatic, persistent, team Collaboration, the game goes beyond the work style, we sincerely welcome customers from all over the world to visit us, seek common development and create brilliant future.
The Leading International Rubber Technology ExhibitionRead More